Legrand CS102
CS102
Importata da documento
| Len | Scala | Endian | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| 0 | Battery Status 1=unknown, 2=battery normal, 3=battery low, 4=battery depleted, 5=battery discharging, 6=battery failure. | battery_status | 4 | uint16 | 1 | 1 | — | R | — | |
| 0 | Battery Bad | battery_bad | 2 | boolean | 1 | 1 | — | R | — | |
| 0 | Config Input Voltage | config_input_voltage | 3 | uint16 | 1 | 1 | V | R/W | — | |
| 1 | Seconds On Battery | seconds_on_battery | 4 | uint32 | 2 | 1 | s | R | — | |
| 1 | On Battery | on_battery | 2 | boolean | 1 | 1 | — | R | — | |
| 1 | Config Input Frequency | config_input_frequency | 3 | uint16 | 1 | 1 | Hz | R/W | — | |
| 2 | Low Battery | low_battery | 2 | boolean | 1 | 1 | — | R | — | |
| 2 | Config Output Voltage | config_output_voltage | 3 | uint16 | 1 | 1 | V | R/W | — | |
| 3 | Estimated Minutes Remaining | estimated_minutes_remaining | 4 | uint16 | 1 | 1 | min | R | — | |
| 3 | Battery Depleted | battery_depleted | 2 | boolean | 1 | 1 | — | R | — | |
| 3 | Config Output Frequency | config_output_frequency | 3 | uint16 | 1 | 1 | Hz | R/W | — | |
| 4 | Estimated Charge Remaining | estimated_charge_remaining | 4 | uint16 | 1 | 1 | % | R | — | |
| 4 | Over Temperature | over_temperature | 2 | boolean | 1 | 1 | — | R | — | |
| 4 | Config Output Apparent Power | config_output_apparent_power | 3 | uint32 | 2 | 1 | VA | R | — | |
| 5 | Battery Voltage | battery_voltage | 4 | uint16 | 1 | 0.1 | V | R | — | |
| 5 | Input Bad | input_bad | 2 | boolean | 1 | 1 | — | R | — | |
| 6 | Battery Current | battery_current | 4 | uint16 | 1 | 0.1 | A | R | — | |
| 6 | Output Bad | output_bad | 2 | boolean | 1 | 1 | — | R | — | |
| 6 | Config Output Active Power | config_output_active_power | 3 | uint32 | 2 | 1 | W | R | — | |
| 7 | UPS Temperature | ups_temperature | 4 | uint16 | 1 | 0.1 | °C | R | — | |
| 7 | Output Overload | output_overload | 2 | boolean | 1 | 1 | — | R | — | |
| 8 | On Bypass | on_bypass | 2 | boolean | 1 | 1 | — | R | — | |
| 8 | Config Low Voltage Transfer Point | config_low_voltage_transfer_point | 3 | uint16 | 1 | 1 | V | R/W | — | |
| 9 | Bypass Bad | bypass_bad | 2 | boolean | 1 | 1 | — | R | — | |
| 9 | Config High Voltage Transfer Point | config_high_voltage_transfer_point | 3 | uint16 | 1 | 1 | V | R/W | — | |
| 10 | Config Over Temperature Set Point (°F) Range: 50~212. Nome duplicato nel documento originale rispetto a 0x000E (stesso dato in °C): indirizzo diverso, mantenuti entrambi. | config_over_temperature_set_point_f | 3 | uint16 | 1 | 1 | °F | R/W | — | |
| 12 | Charger Failed | charger_failed | 2 | boolean | 1 | 1 | — | R | — | |
| 12 | Config Low Battery Time | config_low_battery_time | 3 | uint16 | 1 | 1 | min | R/W | — | |
| 13 | Config Audible Status 1=disabled, 2=enabled, 3=muted. | config_audible_status | 3 | uint16 | 1 | 1 | — | R/W | — | |
| 14 | Config Over Temperature Set Point (°C) Range: 10~100. Nome duplicato nel documento originale rispetto a 0x000A (stesso dato in °F): indirizzo diverso, mantenuti entrambi. | config_over_temperature_set_point_c | 3 | uint16 | 1 | 1 | °C | R/W | — | |
| 15 | Fan Failure | fan_failure | 2 | boolean | 1 | 1 | — | R | — | |
| 16 | Input Line Bad Contatore. | input_line_bad | 4 | uint16 | 1 | 1 | — | R | — | |
| 16 | Fuse Failure | fuse_failure | 2 | boolean | 1 | 1 | — | R | — | |
| 16 | Shutdown Type 1=output, 2=system. | shutdown_type | 3 | uint16 | 1 | 1 | — | R/W | — | |
| 17 | Input Number of Lines | input_number_of_lines | 4 | uint16 | 1 | 1 | — | R | — | |
| 17 | General Fault | general_fault | 2 | boolean | 1 | 1 | — | R | — | |
| 17 | Shutdown After Delay | shutdown_after_delay | 3 | uint32 | 2 | 1 | s | R/W | — | |
| 18 | Input Frequency phase 1 | input_frequency_phase_1 | 4 | uint16 | 1 | 0.1 | Hz | R | — | |
| 18 | Diagnostic Test Failed | diagnostic_test_failed | 2 | boolean | 1 | 1 | — | R | — | |
| 19 | Input Frequency phase 2 | input_frequency_phase_2 | 4 | uint16 | 1 | 0.1 | Hz | R | — | |
| 19 | Communications Lost | communications_lost | 2 | boolean | 1 | 1 | — | R | — | |
| 19 | Startup After Delay | startup_after_delay | 3 | uint32 | 2 | 1 | s | R/W | — | |
| 20 | Input Frequency phase 3 | input_frequency_phase_3 | 4 | uint16 | 1 | 0.1 | Hz | R | — | |
| 21 | Input Voltage phase 1 | input_voltage_phase_1 | 4 | uint16 | 1 | 0.1 | V | R | — | |
| 21 | Reboot After Delay Range: 1~300. | reboot_after_delay | 3 | uint32 | 2 | 1 | s | R/W | — | |
| 22 | Input Voltage phase 2 | input_voltage_phase_2 | 4 | uint16 | 1 | 0.1 | V | R | — | |
| 23 | Input Voltage phase 3 | input_voltage_phase_3 | 4 | uint16 | 1 | 0.1 | V | R | — | |
| 23 | Test In Progress | test_in_progress | 2 | boolean | 1 | 1 | — | R | — | |
| 23 | Auto Restart Action 1=on, 2=off. | auto_restart_action | 3 | uint16 | 1 | 1 | — | R/W | — | |
| 24 | Input Current phase 1 | input_current_phase_1 | 4 | uint16 | 1 | 0.1 | A | R | — | |
| 24 | Ups Sleep Time Setting Range: 0~10000. | ups_sleep_time_setting | 3 | uint16 | 1 | 1 | min | R/W | — | |
| 25 | Input Current phase 2 | input_current_phase_2 | 4 | uint16 | 1 | 0.1 | A | R | — | |
| 25 | Ups Control Setting 1=turn off UPS, 2=put UPS to sleep mode, 3=turn on UPS/cancel shutdown, 4=none (default). | ups_control_setting | 3 | uint16 | 1 | 1 | — | R/W | — | |
| 26 | Input Current phase 3 | input_current_phase_3 | 4 | uint16 | 1 | 0.1 | A | R | — | |
| 26 | UPS Shutdown Delay | ups_shutdown_delay | 3 | uint16 | 1 | 1 | s | R/W | — | |
| 27 | Input Active Power phase 1 | input_active_power_phase_1 | 4 | uint32 | 2 | 1 | W | R | — | |
| 29 | Input Active Power phase 2 | input_active_power_phase_2 | 4 | uint32 | 2 | 1 | W | R | — | |
| 31 | Input Active Power phase 3 | input_active_power_phase_3 | 4 | uint32 | 2 | 1 | W | R | — | |
| 48 | Output Source 1=other, 2=none, 3=normal, 4=bypass, 5=battery, 6=booster, 7=reducer. | output_source | 4 | uint16 | 1 | 1 | — | R | — | |
| 48 | Battery Test Action 0=none (default), 1=quick battery test, 2=battery test until battery low, 3=timed battery test, 4=cancel active battery test, 5=clear last battery test results. | battery_test_action | 3 | uint16 | 1 | 1 | — | R/W | — | |
| 49 | Output Number Lines | output_number_lines | 4 | uint16 | 1 | 1 | — | R | — | |
| 49 | Battery Test Setting Time (Control) Nome duplicato nel documento originale rispetto a 0x0070 del gruppo Tests: indirizzo diverso, mantenuti entrambi. | battery_test_setting_time_control | 3 | uint16 | 1 | 1 | min | R/W | — | |
| 50 | Output Frequency phase 1 | output_frequency_phase_1 | 4 | uint16 | 1 | 0.1 | Hz | R | — | |
| 53 | Output Voltage phase 1 | output_voltage_phase_1 | 4 | uint16 | 1 | 0.1 | V | R | — | |
| 54 | Output Voltage phase 2 | output_voltage_phase_2 | 4 | uint16 | 1 | 0.1 | V | R | — | |
| 55 | Output Voltage phase 3 | output_voltage_phase_3 | 4 | uint16 | 1 | 0.1 | V | R | — | |
| 56 | Output Current phase 1 | output_current_phase_1 | 4 | uint16 | 1 | 0.1 | A | R | — | |
| 57 | Output Current phase 2 | output_current_phase_2 | 4 | uint16 | 1 | 0.1 | A | R | — | |
| 58 | Output Current phase 3 | output_current_phase_3 | 4 | uint16 | 1 | 0.1 | A | R | — | |
| 59 | Output Active Power phase 1 | output_active_power_phase_1 | 4 | uint32 | 2 | 1 | W | R | — | |
| 61 | Output Active Power phase 2 | output_active_power_phase_2 | 4 | uint32 | 2 | 1 | W | R | — | |
| 63 | Output Active Power phase 3 | output_active_power_phase_3 | 4 | uint32 | 2 | 1 | W | R | — | |
| 65 | Output Percent Load phase 1 | output_percent_load_phase_1 | 4 | uint16 | 1 | 0.1 | % | R | — | |
| 66 | Output Percent Load phase 2 | output_percent_load_phase_2 | 4 | uint16 | 1 | 0.1 | % | R | — | |
| 67 | Output Percent Load phase 3 | output_percent_load_phase_3 | 4 | uint16 | 1 | 0.1 | % | R | — | |
| 68 | Output Apparent Power phase 1 | output_apparent_power_phase_1 | 4 | uint32 | 2 | 1 | VA | R | — | |
| 70 | Output Apparent Power phase 2 | output_apparent_power_phase_2 | 4 | uint32 | 2 | 1 | VA | R | — | |
| 72 | Output Apparent Power phase 3 | output_apparent_power_phase_3 | 4 | uint32 | 2 | 1 | VA | R | — | |
| 80 | Bypass Number Lines | bypass_number_lines | 4 | uint16 | 1 | 1 | — | R | — | |
| 81 | Bypass Frequency phase 1 | bypass_frequency_phase_1 | 4 | uint16 | 1 | 0.1 | Hz | R | — | |
| 84 | Bypass Voltage phase 1 | bypass_voltage_phase_1 | 4 | uint16 | 1 | 0.1 | V | R | — | |
| 85 | Bypass Voltage phase 2 | bypass_voltage_phase_2 | 4 | uint16 | 1 | 0.1 | V | R | — | |
| 86 | Bypass Voltage phase 3 | bypass_voltage_phase_3 | 4 | uint16 | 1 | 0.1 | V | R | — | |
| 87 | Bypass Current phase 1 | bypass_current_phase_1 | 4 | uint16 | 1 | 0.1 | A | R | — | |
| 88 | Bypass Current phase 2 | bypass_current_phase_2 | 4 | uint16 | 1 | 0.1 | A | R | — | |
| 89 | Bypass Current phase 3 | bypass_current_phase_3 | 4 | uint16 | 1 | 0.1 | A | R | — | |
| 90 | Bypass Active Power phase 1 | bypass_active_power_phase_1 | 4 | uint32 | 2 | 1 | W | R | — | |
| 92 | Bypass Active Power phase 2 | bypass_active_power_phase_2 | 4 | uint32 | 2 | 1 | W | R | — | |
| 94 | Bypass Active Power phase 3 | bypass_active_power_phase_3 | 4 | uint32 | 2 | 1 | W | R | — | |
| 112 | Battery Test Setting Time (Tests) Nome duplicato nel documento originale rispetto a 0x0031 del gruppo Control: indirizzo diverso, mantenuti entrambi. | battery_test_setting_time_tests | 3 | uint16 | 1 | 1 | min | R/W | — | |
| 113 | Battery Test Result 1=done passed, 2=done warning, 4=aborted, 5=in progress, 6=no test initiated (default). | battery_test_result | 3 | uint16 | 1 | 1 | — | R | — | |
| 114 | Battery Test Start Time Timestamp. | battery_test_start_time | 3 | uint32 | 2 | 1 | — | R | — | |
| 116 | Battery Test Elapsed Time Timeticks. | battery_test_elapsed_time | 3 | uint32 | 2 | 1 | — | R | — | |
| 145 | UPS Type 1=On-Line, 2=Off-Line, 3=Line-Interactive, 4=Three Phase/Three phase, 5=Other, 10=Three-phase/Single phase. | ups_type | 4 | uint16 | 1 | 1 | — | R | — |
Leggi questi registri via API
curl https://busbabel.vercel.app/api/devices/legrand/cs102/registers?version=v1